Booking today · Houston · three-hour arrival windows Independent Bosch specialists · Licensed & insured Mon–Fri 7:00 AM - 8:00 PM · Sat 8:00 AM - 6:00 PM
(713) 568-9298 Schedule a Visit
Safety & Risks · 4 min read

Bosch AquaStop Alert: What the Leak Warning Means

A Bosch AquaStop alert means a sensor found water and shut the supply. Close the valve, check for a leak, and do not press Start until the cause is found.

A Bosch AquaStop alert means the machine sensed water where none should be and closed the water supply so a leak cannot grow. Turn off the water valve, check the floor and cabinet for dampness, and do not press Start. Treat the leak as real until a technician shows otherwise.

What does the AquaStop alert actually mean?

Finding your washer or dishwasher halted with an alert can feel like a failure. In reality the machine just did its job. AquaStop is Bosch’s leak protection: when a sensor or float detects moisture, the inlet is closed so the leak cannot keep growing.

The alert is a protective stop, not a broken display. It tells you that water was detected, but it does not tell you whether the water came from a hose, a seal, the pump, or simple condensation. That is why the next steps matter.

Which code will you see?

Both codes belong to the same family of leak protection, so the first response is identical: stop, close the water, and look for the source before doing anything else.

On washers with an Aquastop switch the alert appears as Er:17. On a dishwasher it shows as E15. The machines differ, but the idea is the same: a sensor or float found moisture and the inlet was shut.

Write the code down exactly as shown, or take a photo of the display. It helps when a technician plans the visit, and it separates a leak alert from other messages that look similar.

What should you do right away?

  1. Turn off the water valve that feeds the appliance.
  2. Check the floor, the cabinet, and the wall behind for dampness.
  3. Leave the cycle alone. Pressing Start to see if the message disappears only invites more water.

Unplug the appliance or switch off its breaker before reaching behind it or moving it, especially if the floor is wet. Water and household current do not mix, and a puddle near an outlet changes the safety picture. In Houston homes, where washers often sit in closets or garages and dishwashers sit above wood or laminate flooring, even a slow leak can spread before anyone notices.

Is a false alarm still worth checking?

Condensation or a worn float switch can set off AquaStop with no puddle in sight. Even then, you cannot be sure from the outside. A real drip from a hose, seal, or pump looks the same on the display as a harmless trigger, so the inspection is what separates the two.

Assume the leak is real until a technician shows otherwise. Mopping up a small puddle is a minor annoyance; repairing a soaked subfloor is not. Humid weather can add to the confusion, since moisture inside the base can form without any hose failing.

The table below shows common situations and what each usually means.

Situation Likely cause What you can check When to call
Alert and a puddle Leaking hose, seal, or pump Shut the supply valve and look for the source Right away
Alert and damp cabinet Slow drip that reached the cabinet floor Dry the area and check for returning moisture As soon as possible
Alert, nothing visible Stuck float or moisture in the base Look under and behind the unit Yes, to rule out a real leak
Alert returns after a restart Leak or sensor problem still present Do not keep restarting Before using it again
Alert after moving the unit Disturbed hose or float Check hose positions without forcing If it will not clear

When should you call a technician?

Do not wait for a second alert. A repeat means the cause is still there, and every cycle after that can add water to the floor, the cabinet, and the wall behind the unit.

Call as soon as you see the alert, whether or not you find water. If you do find water, shut the supply first and keep the appliance off. When you describe the problem, mention which room the appliance is in, whether you saw water, and the code on the display, so the technician can plan the right tools and floor protection before arriving.

Frequently asked questions

Can I reset the alert myself?

You can try, but a cleared screen proves nothing about the cause. If water caused the stop, running the cycle again can push more water onto the floor. Check for a leak first and keep the supply closed.

Why does the alert appear when I see no water?

A float can stick, and condensation or moisture in the base can trip it. A small drip from a hose or seal can also hide underneath the machine. Only an inspection tells them apart.

Is it safe to use the appliance after AquaStop trips?

Not until the cause is known. The protection stopped the water for a reason. Leave the supply closed and the appliance off until a technician has checked hoses, seals, and the pump.

Should I shut off the water even if the floor looks dry?

Yes. Closing the supply valve costs nothing and prevents a surprise if the leak is hidden. Keep it closed until the appliance has been inspected and you know the alert was a harmless trigger.

Sources

Tell us the model and the code. We will bring the part.

(713) 568-9298 Schedule a Visit
☎ Call our office ▤ Schedule a Visit