A Bosch dishwasher showing E15 has detected water in its base pan through the AquaStop float switch and closed the inlet. Close the supply valve, check the floor and cabinet for water, and do not press Start again. Real leak or false alarm needs a look at the hoses, seal, and pump.
What does E15 mean on a Bosch dishwasher?
You open the kitchen and the dishwasher is silent, the cycle is dead, and the display reads E15. That code comes from the AquaStop system: a float switch in the base pan sensed water and closed the inlet so nothing could overflow. The machine is protecting your floor, so give it a calm, orderly response.
The float is a simple safety device. It does not tell you where the water came from, only that water was in the pan, which is why a quick floor check comes first.
What should you do first?
Work with dry hands and a dry floor. If the floor is wet near the outlet, switch off the breaker before you touch anything.
- Close the supply valve, usually under the sink or behind the kickplate.
- Look at the floor around the unit and inside the cabinet next to it for puddles or damp wood.
- If the area is clear, ease the dishwasher forward a few inches and check beneath the front edge.
Keep the movement gentle. Tipping the machine can slosh water around inside the base, and the pan itself is not something to open at home. Unplug the dishwasher or switch off its breaker before pulling it forward, since the wiring runs near the base.
What should you leave alone?
Resist the urge to press Start again just to see whether the message disappears. If a hose, seal, or pump really is dripping, another run will push more water onto the floor and into the cabinetry. A cleared screen proves nothing about the cause.
Do not tilt the dishwasher or drain the base by hand, and do not use a hair dryer to dry the float area. Heat and moisture near the sensor can mislead the next test.
Is it a real leak or a false alarm?
A dishwasher that has leaked once may leak again. Even when the cause is minor, it is worth fixing before the next cycle.
The float can stick, and moisture inside the pan can sometimes trip it, so E15 does not always mean a puddle exists. In humid Houston kitchens, condensation under a dishwasher after a hot cycle can add to this. Telling a genuine leak from a false trigger means looking at the hoses, door seal, and pump with the base accessible. That is work for a technician rather than a guess.
The table below shows what each situation usually points to.
| What you find | Likely cause | What you can check | When to call |
|---|---|---|---|
| Water on the floor | Leaking hose, seal, or pump | Close the valve, dry the area, note where it started | Right away |
| Damp cabinet beside the unit | Slow drip or overflow | Check wood for swelling | As soon as possible |
| Dry floor, E15 still shown | Stuck float or moisture in the base | Look beneath the front edge | Yes, to rule out a leak |
| E15 returns after a restart | Leak still present | Do not keep restarting | Before using it again |
| E15 after the unit was moved | Disturbed hose or float | Check the hose for kinks | If it will not clear |
What is the next step?
When you describe the problem, mention whether you found water, where the supply valve is, and whether the dishwasher sits against wood cabinets or tile. These details help the technician plan the work and protect your floor.
Do not run hot water through the sink to test the drain while the dishwasher is connected, because a shared drain can send water back toward the unit.
Having a towel and a flashlight nearby makes the floor check quicker, and a photo of the display helps when you describe the problem. Once the water is off and the floor is dry, keep the supply closed until the dishwasher has been inspected. Treat E15 as an urgent message, because water that reaches wood cabinets or flooring does damage fast.
Frequently asked questions
Can I clear E15 by pressing Start?
You can try, but that is not advised. A cleared screen does not show what caused the stop, and a second run can push more water onto the floor if there is a real leak.
Why does my dishwasher show E15 with no water on the floor?
The float switch can stick, and moisture or condensation in the base pan can trip it. A slow leak can also hide beneath the machine. An inspection tells these apart.
Is it safe to use the dishwasher while E15 is showing?
No. Keep the supply valve closed and the machine off. The system stopped the water for a reason, and running it again without finding the cause can lead to water damage.
Where is the dishwasher shutoff valve?
It is usually under the kitchen sink or behind the kickplate at the bottom front of the dishwasher. If you cannot find it, switch off the water to the home at the main valve until you do.